Morgansfort Pregen Character 3D Models
- Solomoriah
- Site Admin
- Posts: 12461
- Joined: Thu Nov 13, 2008 8:15 pm
- Location: LaBelle, Missouri
- Contact:
Morgansfort Pregen Character 3D Models
I've created a set of 3D printable models for the eight pregenerated characters from BF1 Morgansfort, using my "Two Cent Base" for stability. These figures were designed by others and shared under various Creative Commons licenses, which is how I, a non-artist, was able to put this set together.
You can get the files here: https://www.thingiverse.com/thing:5207468
You can get the files here: https://www.thingiverse.com/thing:5207468
My personal site: www.gonnerman.org
- Solomoriah
- Site Admin
- Posts: 12461
- Joined: Thu Nov 13, 2008 8:15 pm
- Location: LaBelle, Missouri
- Contact:
Re: Morgansfort Pregen Character 3D Models
Here are some pics:
- Attachments
-
- Intro Story Characters.png (315.84 KiB) Viewed 2313 times
-
- Alternate Characters.png (404.08 KiB) Viewed 2313 times
My personal site: www.gonnerman.org
- Solomoriah
- Site Admin
- Posts: 12461
- Joined: Thu Nov 13, 2008 8:15 pm
- Location: LaBelle, Missouri
- Contact:
Re: Morgansfort Pregen Character 3D Models
And no, I did not realize I'd used the same model for Apoqulis and Darion. I'll likely find an alternative for one of them, but for now it's good enough.
My personal site: www.gonnerman.org
- FakeHealer
- Posts: 101
- Joined: Fri Oct 16, 2020 2:25 pm
Re: Morgansfort Pregen Character 3D Models
very cool.
It seems to almost creates a "box set" feel if someone prints them out, gets a double-sided poster print size map or 2 and tosses it all together.
It seems to almost creates a "box set" feel if someone prints them out, gets a double-sided poster print size map or 2 and tosses it all together.
Re: Morgansfort Pregen Character 3D Models
Great work as with the pig faced orc!
Teaman is the sole proprietor of Sharp Mountain Games at roll20 and DTRPG
https://marketplace.roll20.net/browse/p ... tain-games
http://drivethrurpg.com/browse/pub/8418 ... tain-Games
https://marketplace.roll20.net/browse/p ... tain-games
http://drivethrurpg.com/browse/pub/8418 ... tain-Games
Re: Morgansfort Pregen Character 3D Models
Very cool! Out of curiosity, which support settings did you use Solo?
- Solomoriah
- Site Admin
- Posts: 12461
- Joined: Thu Nov 13, 2008 8:15 pm
- Location: LaBelle, Missouri
- Contact:
Re: Morgansfort Pregen Character 3D Models
Tree supports, touching baseplate, otherwise with default options. Always. I've tried printing them tipped back at an angle, but I can't get a clean separation from the supports and the bases are always nasty and rough. So I just print them upright with tree supports.
My personal site: www.gonnerman.org
Re: Morgansfort Pregen Character 3D Models
Thanks for that. I tried a few prints with tree supports touching baseplate. My first Morningstar print came out OK, but her ankles weren't strong enough - I dropped her and she snapped off there.
Barthal and Bork both came out great without any supports - but I had a lot of trouble with Apoqulis' mace and shield with just tree supports touching baseplate. I sliced him on his back with the mace upright but like you said the base came out rough.
I'll need to try a few more prints, am still learning the "art" of 3D printing
Barthal and Bork both came out great without any supports - but I had a lot of trouble with Apoqulis' mace and shield with just tree supports touching baseplate. I sliced him on his back with the mace upright but like you said the base came out rough.
I'll need to try a few more prints, am still learning the "art" of 3D printing
- Solomoriah
- Site Admin
- Posts: 12461
- Joined: Thu Nov 13, 2008 8:15 pm
- Location: LaBelle, Missouri
- Contact:
Re: Morgansfort Pregen Character 3D Models
What filament are you using?
My personal site: www.gonnerman.org
Re: Morgansfort Pregen Character 3D Models
eSUN PLA+ on an Ender 3 v2, using the Fat Dragon Games Cura profile.
Who is online
Users browsing this forum: Google [Bot] and 53 guests